Insulation
Rigid insulation and a cover board form the base under the rubber.
Flat Roofing
Rubber Roof Installation Rutherford, NJ
A roofer in Rutherford can install a rubber roof by laying EPDM membrane in wide sheets over insulation and a cover board, bonding or fastening it down and sealing every seam with primer and tape, and explain each choice before the sheet is rolled out. Call (551) 380-1579 to reach a local roofer.
EPDM is the material most people mean when they say rubber roof. EPDM is sold in wide rolls, typically 45 or 60 mil thick, and it stretches and recovers as the roof moves through hot and cold seasons. Its seams are joined with primer and tape instead of hot air.
EPDM can be attached in three main ways. The sheet can be glued to the substrate, fastened with plates at the seams or laid loose under a layer of stone. Residential roofs are most often fully adhered.
Two more decisions round out the plan. Sixty mil EPDM costs a little more than 45 mil but resists punctures better and lasts longer. White EPDM suits sunny roofs, and black suits cooler climates. The installer also plans how the membrane laps under shingles above it and up the wall beside it, where leaks tend to start.
Depending on what the roofer finds, rubber roof installation in Rutherford, NJ can go hand in hand with rubber roof repair and flat roof installation.
Looking for Rutherford rubber roof installation? Call (551) 380-1579 and describe the problem to a roofer who works in Rutherford.
Call nowThe process
The rubber roof installation process
Each layer is set up to give the membrane a smooth, solid base.
Check the base
The roofer checks the deck for rot, gaps and loose sheets and confirms the roof has enough slope to drain. Old roofing is removed if the roof is being replaced.
Insulation
Insulation boards go down for energy savings and slope, topped by a smooth cover board. Tapered boards add slope where needed.
Lay the sheet
The membrane is unrolled, aligned and allowed to settle before bonding. Seams are planned so they run with the slope.
Apply adhesive
Half the sheet is folded back, adhesive is applied to both surfaces and the rubber is pressed into place. Each half gets the same treatment in turn. Brooming from the middle outward pushes trapped air to the edges.
Seal the seams
Primer and seam tape join the sheets, with T-joints covered by extra patches. Exposed edges get lap sealant.
Flash the details
Flashing goes up walls and around curbs, with boots at pipes and new edge metal at the perimeter. The top edge is sealed and covered. A final walk checks every seam with a probe before the job is closed out.
What is included
What rubber roof installation covers
Seam tape
Every seam gets primer and tape for a lasting bond.
Flashing
Walls, curbs, pipes and edges are flashed to keep water out.
Rubber sheet
Wide sheets of EPDM cover the roof with as few seams as possible.
Tear-off
Old roofing is removed and the deck is repaired before new layers go down.
Related service
EPDM Roof Installation Rutherford, NJ
Installing EPDM well comes down to preparation, seams and flashing. A flat, dry base, properly timed adhesive and carefully primed seams are what make EPDM last. Installers work in dry weather so the bond holds. The field and the flashings may get different adhesives, since vertical surfaces need a stronger grip.
For a Rutherford home, the installer thinks ahead to how the roof will behave over the years. Flashing at walls and curbs is secured with termination bar so the sheet cannot pull loose as it ages, and corners get flexible uncured flashing. Ask how the roofer secures the perimeter.
Local help
Rubber Roof Installation Near Me
In Rutherford, EPDM is a popular choice for low slope roofs on additions and attached garages. Across Rutherford and nearby towns like East Rutherford, Wallington, Carlstadt and North Arlington, EPDM handles storms, sun and cold well when it is installed with good seams and drainage, so installation details matter as much as the material.
Searching for rubber roof installation near me from Rutherford or East Rutherford, Wallington, Carlstadt and North Arlington? Call (551) 380-1579 to talk to a roofer who works in your part of town.
How the weather here affects roofs around Rutherford
Cold winters bring snow, ice and a long stretch of freezing nights. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, building ice dams that push water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. That is why roof repair in Rutherford is busiest after a hard winter and before the next one.
Why call
Why fix it now
Drier ceilings
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Local knowledge
Roofers in Rutherford know the roof types and weather wear common in local homes.
Clear next steps
Ask the roofer about the cause, the options and the estimate before work starts.
Rubber Roof Installation questions
How thick should a rubber roof be?
The common choices are 45 mil and 60 mil. Thicker 60 mil is tougher and longer lasting. Even thicker sheets are available for demanding roofs.
What is the difference between EPDM and TPO?
The two are different materials. EPDM uses taped seams and stays flexible in cold, and TPO uses welded seams and reflects heat. Both are common on flat roofs.
What is the lifespan of a new EPDM roof?
EPDM can last 25 years or longer. Thickness, seam quality and maintenance all affect its life. Patching EPDM is straightforward.
Is it possible to install EPDM over the old roof?
A recover is possible only under certain conditions. The old roof must be a single dry layer, with a recover board over it. If the old roof is wet, it must come off. Core samples or a moisture scan show whether the old roof is dry enough.
What color EPDM is best?
Color affects heat gain. White helps in sunny climates, and black is common where winters are long. Ask about both options.
More questions? Call (551) 380-1579
Related services
Rubber Roof Repair
Fixing open seams, punctures, shrinkage and split flashing on EPDM rubber roofs, after the real leak point is found.
Learn moreFlat Roof Installation
Flat roof installation from the deck and tapered insulation up to the seams, flashing and edge metal, planned around how the roof will be used.
Learn moreTPO Roofing
Heat-welded TPO membrane for flat and low-slope roofs, with seams welded into one watertight sheet.
Learn moreFlat Roof Replacement
Replacing old built-up, torch-down, EPDM or TPO roofs with a new system built to drain, with tapered insulation where water used to sit.
Learn more
Looking for something else?
See all roofing servicesNeed rubber roof installation in Rutherford, NJ?
Call now for Rutherford rubber roof installation and help in the towns around it.